By Hector M., Service expert Allentown office
Job at a glance
- Location
- Allentown, PA
- Service
- Hot Tub and Pool Wiring
- When
- September 2026
- Service expert
- Hector M.
- Called about
- wiring for a hot tub
- Service size
- 100 amp
- Panel brand
- Siemens
- Visits
- 1
- Options offered
- 3
- Inspection passed
- No
What this type of job typically costs
$1,600 to $6,650
Hot tub wiring
From 28 jobs we completed in the last 18 months.
The middle half of what our clients paid for this work alone across Pennsylvania and New Jersey, before discounts, refreshed every month. A licensed service expert sees your home and gives a written price before any work starts.
Range updated November 10, 2026.
About this service →A homeowner in Allentown, Pennsylvania, contacted Thomas Edison Electric to wire a newly installed hot tub. The client had already run conduit under a new concrete pad and needed a licensed electrician to complete the electrical connection.
The client's problem
The client had a hot tub ready for use but needed a proper 240-volt electrical circuit installed. The existing 100-amp Siemens panel did not have enough open spaces to accommodate the new high-amperage circuit required for the spa.
What our service expert found
The service expert evaluated the existing panel and determined there was insufficient space for the dedicated 60-amp circuit the hot tub required. Adding a large circuit like this to a panel without available slots meant either reconfiguring existing breakers or expanding capacity with a subpanel. The client had already prepared conduit under the concrete pad, which simplified the wire routing portion of the project.
Options we presented
The service expert presented three approaches to accommodate the new hot tub circuit while addressing the panel space limitation.
Install the hot tub circuit by adding tandem breakers to free up space in the existing panel
Install a subpanel to provide additional circuit capacity and run the dedicated hot tub line from it (the client chose this one)
Install a subpanel with whole home surge protection along with the dedicated hot tub circuit
The solution
The client chose to install a subpanel to provide the additional circuit capacity needed. The team installed a new Siemens 8-space 100-amp main lug panel as a subpanel, fed by a 60-amp two-pole breaker from the main panel. They ran 6-gauge wire from the subpanel through the existing conduit to a 50-amp GFCI spa disconnect mounted near the hot tub. A tandem breaker was installed in the main panel to free up space for the new feeder circuit. After completing the installation, the team tested voltage and verified proper operation of the entire system.
Work performed
Installed Siemens 8-space 100-amp main lug subpanel
Installed 60-amp two-pole breaker in main panel to feed subpanel
Ran 6-gauge wire from subpanel to spa disconnect location
Installed 50-amp GFCI hot tub disconnect near the spa
Installed tandem breaker to free up panel space
Tested voltage and verified proper system operation
What we installed
- Romex Wire 6/3 NM Price Per Foot× 50
- Eaton BR50SPAST Hot Tub and Spa Panel 50 Amp GFCI
- Siemens BR 15/15 Amp Single Pole Tandem Breaker× 2
- Siemens BR 60 Amp 2 Pole Breaker
- SER Connector 1-1/2" D/C 848S× 2
- Eaton BR120 20 Amp Single Pole Breaker× 4
- Eaton GBK14 14 Terminal Ground Bar Kit
- Siemens Type EQ 8 Space 125 Amp Main Lug Panel
Why pricing varies
No two homes are wired the same. On this job, the price came down to:
- Service size and whether the main breaker rating changes
- Condition of the existing enclosure, bus bars and breakers
- Grounding and bonding that must be brought up to current code at the same time
- Service entrance conductors and the meter can, when they are part of the scope
- Utility coordination and permit requirements in the jurisdiction
- Surge, AFCI and GFCI protection added during the changeout
- Panel brand and breaker selection
- Accessibility of the panel location and any drywall or masonry work around it
- Code corrections found once the deadfront is off
A service expert prices your job after seeing it, and you approve the price before any work starts.
Why it matters in Allentown
Hot tubs draw significant power and require dedicated circuits with GFCI protection to meet electrical codes and ensure safe operation. In older Lehigh Valley homes with 100-amp service, adding a subpanel is often the most practical way to accommodate new high-demand equipment without overloading the main panel. Proper installation protects both the equipment and the home from electrical hazards.
Common questions
Why does a hot tub need its own dedicated circuit?
Hot tubs draw a large amount of power, typically 40 to 60 amp, which is too much to share with other circuits. A dedicated circuit ensures the spa receives consistent power and prevents overloading other parts of your electrical system.
What is a GFCI spa disconnect and why is it required?
A GFCI spa disconnect is a safety device installed near the hot tub that can quickly shut off power and protect against electrical shock. Electrical codes require this protection for hot tubs because water and electricity create a serious shock hazard.
When is a subpanel needed for hot tub installation?
A subpanel is typically needed when your main electrical panel does not have enough open spaces for the new breaker. It provides additional circuit capacity without replacing your entire main panel.
Can I use my existing panel for a hot tub circuit?
It depends on your panel's available space and overall capacity. If your panel has open slots and sufficient amperage, a direct connection may work. If not, a subpanel or breaker reconfiguration may be necessary.
Project photos
Filmed on the job
Watch the walkthrough
Hector M. filmed this on the job in Allentown, so you can see what we found and what the work involved.
The service expert on this job
Hector M.
Service expert
Hector is a service expert with Thomas Edison Electric. He has completed more than 950 jobs for clients in Philadelphia, Bucks and Montgomery counties. His most common calls are lighting and ceiling fans, outlets and switches, troubleshooting and panel upgrades.
More about Hector →Reviewed by a licensed Thomas Edison Electric service expert on November 19, 2026.
Where this job was
Allentown, Pennsylvania, in Lehigh. Electrical service in Allentown
Related
- More new installation case studies
- Hot Tub and Pool Wiring: how we do this job
- More jobs from the Allentown office
- Electrical service in Allentown
- Failed Inspection and a Dead Circuit in Bensalem, PA: Rewiring
- Dead Outlets in Newtown, PA: Scorched GFCI Outlets Replaced and New Smoke Detectors
- More jobs by Hector M.
- Our electrical services
- Contact Thomas Edison Electric



