By Jason Z., Service expert Lebanon office
Job at a glance
- Location
- Lebanon, PA
- Service
- Panel Replacement
- When
- October 2026
- Service expert
- Jason Z.
- Called about
- a problem with the electrical panel
- Service size
- 200 amp
- Panel brand
- Siemens
- Visits
- 2
- Options offered
- 4
- Inspection
- Passed
What this type of job typically costs
$7,425 to $11,875
Panel replacement, everything on the job
From 856 jobs we completed in the last 18 months.
The middle half of what our clients paid for this work alone across Pennsylvania and New Jersey, before discounts, refreshed every month. A licensed service expert sees your home and gives a written price before any work starts.
Range updated November 10, 2026.
About this service →A Lebanon, Pennsylvania homeowner contacted Thomas Edison Electric after noticing serious problems with their electrical panel. The client reported that lights had been flickering for months and discovered melted wires inside the panel the night before.
The client's problem
The client observed flickering lights throughout the home for several months. When they investigated, they found melted insulation on the main feed wires entering the panel, prompting them to shut off about eight breakers as a safety precaution.
What our service expert found
The service expert confirmed the melted wires the client had noticed and discovered an even more serious hazard: evidence that water had been entering the main electrical system. Dried rust and corrosion covered the interior of the panel and the breakers, explaining the flickering and creating a significant fire risk. The expert also determined that the existing system was overloaded and that the home really needed a 200 amp service to handle its electrical demands safely.
Options we presented
The service expert presented four options, from a 100 amp panel and meter replacement to a full 200 amp service upgrade.
100 amp, 20 space Siemens panel and meter with surge protection and an outdoor disconnect
The same 100 amp package with the service cable run in conduit outside
200 amp, 40 space Siemens panel and meter with whole house surge protection, a grounding system and an outdoor disconnect
The same 200 amp package with the service cable run in conduit outside (the client chose this one)
The solution
The client chose the most comprehensive option to address both the immediate safety hazards and the long term capacity needs. The team installed a new 40 space 200 amp Siemens main breaker panel along with a new meter base and outdoor disconnect. They ran the service entrance cable through PVC conduit for protection and added a whole house surge protective device. A full grounding system was installed to ensure proper electrical safety, and a new GFCI receptacle was added where needed. The work required two visits and passed electrical inspection.
Work performed
Installed new 40 space 200 amp Siemens main breaker panel
Replaced meter base with new 200 amp service mast and outdoor disconnect
Ran service entrance cable through PVC conduit for protection
Added whole house surge protective device
Installed full grounding system
Installed GFCI receptacle
What we installed
- Mulberry 76401, 1G Decora Semi Gloss White Metal Plate
- Pass & Seymour 1597-TRW 15A 125V Self-Test GFCI Tamper-Resistant, White Outlet
- Siemens BR 15 Amp Single Pole Breaker× 12
- Siemens BR Q120 20 Amp Single Pole Breaker× 12
- Siemens BR 20 Amp 2 Pole Breaker
- Siemens BR 30 Amp 2 Pole Breaker
- Siemens BR 50 Amp 6 AWG 2 Pole Breaker
- Siemens ec3gb212 21-Position Ground Bar Kit
- Eaton CHSPT2ULTRA Type 1 Surge Protective Device
- Acorn Clamp 5 and 8 Acorn Direct Burial Bronze Ground Rod Clamp× 2
- Ground Clamp Aluminum 1 and 2 to 1"
- Intersystem Bonding Grounding Bridge - ARLGB5
Why pricing varies
No two homes are wired the same. On this job, the price came down to:
- Service size and whether the main breaker rating changes
- Condition of the existing enclosure, bus bars and breakers
- Grounding and bonding that must be brought up to current code at the same time
- Service entrance conductors and the meter can, when they are part of the scope
- Utility coordination and permit requirements in the jurisdiction
- Surge, AFCI and GFCI protection added during the changeout
- Panel brand and breaker selection
- Accessibility of the panel location and any drywall or masonry work around it
- Code corrections found once the deadfront is off
A service expert prices your job after seeing it, and you approve the price before any work starts.
Why it matters in Lebanon
Homes in Lebanon and throughout central Pennsylvania often have aging electrical systems that were not designed for modern power demands. Water intrusion into electrical equipment is particularly dangerous because corrosion weakens connections over time, creating heat buildup that can lead to fires. Upgrading to a properly sized panel with surge protection and a complete grounding system helps protect both the home and the appliances inside it.
Common questions
Why would water get into an electrical panel?
Water can enter through deteriorated weatherheads, damaged conduit, or gaps around the meter base. Over time, this moisture causes rust and corrosion on connections and breakers, which can lead to overheating and electrical failures.
What causes wires to melt inside an electrical panel?
Melted wires typically result from loose connections, corrosion, or overloaded circuits that generate excessive heat. When connections degrade, resistance increases and creates hot spots that can damage insulation and potentially start fires.
Why would I need to upgrade from 100 amp to 200 amp?
Many older homes were wired for lower electrical demands than modern households require. If your panel is frequently overloaded or you plan to add appliances, electric vehicle charging, or HVAC equipment, a 200 amp service provides the capacity needed to run everything safely.
Is it safe to keep using a panel that has melted wires?
No. Melted insulation means a connection has been overheating, and it can get worse without warning. Turn off the affected breakers if you can do it safely, keep clear of the panel and have a licensed electrician inspect it before those circuits go back into use.
Project photos
The service expert on this job
Jason Z.
Service expert
Jason is a service expert with Thomas Edison Electric. He has completed more than 2,400 jobs for clients in Berks, Dauphin and Lebanon counties. His most common calls are troubleshooting, outlets and switches, panel upgrades and lighting and ceiling fans.
More about Jason →Reviewed by a licensed Thomas Edison Electric service expert on November 9, 2026.
Where this job was
Lebanon, Pennsylvania, in Lebanon. Electrical service in Lebanon
Related
- More panel upgrade case studies
- Panel Replacement: how we do this job
- More jobs from the Lebanon office
- Electrical service in Lebanon
- Rusted Panel Found Before a Home Purchase in Lebanon, PA: 200 Amp Panel and Service Upgrade
- Smoke From the Electrical Panel in Lebanon, PA: 200 Amp Panel and Service Upgrade
- More jobs by Jason Z.
- Our electrical services
- Contact Thomas Edison Electric




